 |
|
8. Appendix: Differences between ipchains and ipfwadm.
Some of these changes are a result of kernel changes, and some a
result of ipchains being different from ipfwadm.
- Many arguments have been remapped: capitals now indicates a command, and lower case now indicates an option.
- Arbitrary chains are supported, so even built-in chains have full names instead of flags (eg. `input' instead of `-I').
- The `-k' option has vanished: use `! -y'.
- The `-b' option actually inserts/appends/deletes two rules, rather than a single `bidirectional' rule.
- The `-b' option can be passed to `-C' to do two checks (one in each direction).
- The `-x' option to `-l' has been replaced by `-v'.
- Multiple source and destination ports are not supported anymore. Hopefully being able to negate the port range will somewhat make up for that.
- Interfaces can only be specified by name (not address). The old semantics got silently changed in the 2.1 kernel series anyway.
- Fragments are examined, not automatically allowed through.
- Explicit accounting chains have been done away with.
- Arbitrary protocols over IP can be tested for.
- The old behavior of SYN and ACK matching (which was previously ignored for non-TCP packets) has changed; the SYN option is not valid for non-TCP-specific rules.
- Counters are now 64-bit on 32-bit machines, not 32-bit.
- Inverse options are now supported.
- ICMP codes are now supported.
- Wildcard interfaces are now supported.
- TOS manipulations are now sanity-checked: the old kernel code would silently stop you from (illegally) manipulating the `Must Be Zero' TOS bit; ipchains now returns an error if you try, as well as for other illegal cases.
8.1 Quick-Reference table.
[ Mainly, command arguments are UPPER CASE, and option arguments are lower case ]
One thing to note, masquerading is specified by `-j MASQ'; it is
completely different from `-j ACCEPT', and not treated as merely a
side-effect, unlike ipfwadm does.
================================================================ | ipfwadm | ipchains | Notes ---------------------------------------------------------------- | -A [both] | -N acct | Create an `acct' chain | |& -I 1 input -j acct | and have output and input | |& -I 1 output -j acct | packets traverse it. | |& acct | ---------------------------------------------------------------- | -A in | input | A rule with no target ---------------------------------------------------------------- | -A out | output | A rule with no target ---------------------------------------------------------------- | -F | forward | Use this as [chain]. ---------------------------------------------------------------- | -I | input | Use this as [chain]. ---------------------------------------------------------------- | -O | output | Use this as [chain]. ---------------------------------------------------------------- | -M -l | -M -L | ---------------------------------------------------------------- | -M -s | -M -S | ---------------------------------------------------------------- | -a policy | -A [chain] -j POLICY | (but see -r and -m). ---------------------------------------------------------------- | -d policy | -D [chain] -j POLICY | (but see -r and -m). ---------------------------------------------------------------- | -i policy | -I 1 [chain] -j POLICY| (but see -r and -m). ---------------------------------------------------------------- | -l | -L | ---------------------------------------------------------------- | -z | -Z | ---------------------------------------------------------------- | -f | -F | ---------------------------------------------------------------- | -p | -P | ---------------------------------------------------------------- | -c | -C | ---------------------------------------------------------------- | -P | -p | ---------------------------------------------------------------- | -S | -s | Only takes one port or | | | range, not multiples. ---------------------------------------------------------------- | -D | -d | Only takes one port or | | | range, not multiples. ---------------------------------------------------------------- | -V | <none> | Use -i [name]. ---------------------------------------------------------------- | -W | -i | ---------------------------------------------------------------- | -b | -b | Now actually makes 2 rules. ---------------------------------------------------------------- | -e | -v | ---------------------------------------------------------------- | -k | ! -y | Doesn't work unless | | | -p tcp also specified. ---------------------------------------------------------------- | -m | -j MASQ | ---------------------------------------------------------------- | -n | -n | ---------------------------------------------------------------- | -o | -l | ---------------------------------------------------------------- | -r [redirpt] | -j REDIRECT [redirpt] | ---------------------------------------------------------------- | -t | -t | ---------------------------------------------------------------- | -v | -v | ---------------------------------------------------------------- | -x | -x | ---------------------------------------------------------------- | -y | -y | Doesn't work unless | | | -p tcp also specified. ----------------------------------------------------------------
8.2 Examples of translated ipfwadm commands
Old command: ipfwadm -F -p deny
New command: ipchains -P forward DENY
Old command: ipfwadm -F -a m -S 192.168.0.0/24 -D 0.0.0.0/0
New command: ipchains -A forward -j MASQ -s 192.168.0.0/24 -d 0.0.0.0/0
Old command: ipfwadm -I -a accept -V 10.1.2.1 -S 10.0.0.0/8 -D 0.0.0.0/0
New command: ipchains -A input -j ACCEPT -i eth0 -s 10.0.0.0/8 -d 0.0.0.0/0
(Note that there is no equivalent for specifying interfaces by address: use the interface name. On this machine, 10.1.2.1 corresponds to eth0).
Next Previous Contents
Hosting by: Hurra Communications Ltd.
Generated: 2007-01-26 17:58:10